2007 - 2019 TOYOTA TUNDRA 2WD & 4WD
Are aftermarket upper control arms required on the 2007 - 2019 Tundra systems?
No, aftermarket up control arms are not required on 07-19 Toyota Tundra. Tundra UCA’s provide enough alignment adjustment to set the vehicle within the factory alignment spec range. Lifting the vehicle over 2.5” on some vehicles the stock upper contr
My 2007-2019 Toyota Tundra is leaning to the driver side, what can be done to remedy this?
Toyotas are designed and built with a bias to the driver side due to weight. Toyota Tundras have both the battery and gas tank on the driver side. New vehicles have this lean right off the showroom floor but is not typically noticed until a suspensio
Can the ICON shock boot kit be fitted on Toyota Tundra RXT shocks?
No, due to the unique design of the ICON RXT rear Tundra shock a traditional shock boot is not available for this application. The shock boot design requires it to mount to the cylinder body in the lower right end but the RXT shock does not have a mo
Do 2007 - 2019 Tundra shocks fit on 2002 - 2006 Tundra?
No, the platforms from first GEN 02-06 Tundra to 07-19 second and third GEN Tundra are entirely different. ICON coilovers for first GEN Tundra‘s will not fit on newer your model trucks and vice versa. The rear shocks will not work either, the 07-19 T
Will the ICON 0-1.5” lift rear shock work with higher lift heights on this on 2007 - 2019 Toyota Tundra?
Yes, the ICON rear shock is compatible with higher lift height. The 0-1.5” recommendation is based on optimum ride quality for the vehicle. Using the ICON shock on higher lift applications may function correctly without damage but right quality may s
Can Toyota 200 Series Land Cruiser upper control arms work on Toyota Tundra’s?
No, the Toyota Land Cruiser and Toyota Tundra may seem similar but the lengths of the control arms are in fact different. The Land Cruiser 200 series and Toyota Tundra have their own length control arms as well as different ball joint tapers so they
Are ICON S2 shock system compatible with the Tundra TRD Big Brake kit?
No, the Tundra TRD Big Brake kit will come in contact with the secondary shock at full lock. Modifications can be made to the steering to limit his clearance or limit his contact but the system will require custom installation to avoid interference.
Can the ICON standard/non-RXT shocks be converted to RXT?
No, the vast majority of the components in the RXT version shocks is different than the standard shocks. The RXT Series are comprised of a different cylinder, shaft, and rodend combination compared to their non-RXT counter parts. It is not a cost-eff
What is the nitrogen charge pressure on 2007 - 2019 Toyota Tundra coilovers?
Toyota Tundra coilovers are preset from the factory at 250 psi. (ICON Part Number's: 58650). Toyota Tundra remote reservoir coilovers are preset at 250 psi. (ICON Part Number's: 58750). Remote reservoir CDCV adjustable coilovers are charged to 150 ps
How much lift over stock do the ICON 2007 - 2019 Toyota Tundra coilovers provide out of the box?
ICON coilover kits are preset out of the box at the optimum balance between compression and droop travel to give the best ride quality. The ICON coilovers yield approximately 2” of lift overstock from factory setting. Motor size, door configuration,
Can ICON 2007 - 2019 Tundra upper control arms work with long travel suspension systems?
No, ICON upper control arms are designed to work with a stock width vehicle. Aftermarket long travel systems will require upper and lower control arms that are longer then stock to increase the track width and wheel travel of the vehicle.
Can ICON 2007 - 2019 Tundra uniball UCA’s be upgraded to Delta Joints?
All ICON upper control arms, billet aluminum and tubular steel, can be retrofitted to Delta Joints. Delta Joint upgrade kits are sold based on vehicle model. The ICON UCA kit for 07-19 Tundra’s is available in billet aluminum billet aluminum and tubu
Are differential drop spacers required on 07-19 Tundra suspension systems?
No, front differential drop spacers are not required for ICON suspension systems
Will ICON kits work with TRD Pro Tundras?
Yes. ICON suspension systems are compatible with TRD Pro trim level Toyota Tundras. TRD Pro models are set with a slightly higher ride height compared to non-Pro models. The max lift provided by ICON suspension systems will be less on Pro models due
Can the ICON 2007-UP Tundra upper control arms be used with an existing 6” subframe/drop bracket kit?
Not all 6” subframe systems are compatible with ICON's Toyota Tundra tubular steel upper control arms. Variations in lift kit design will at times yield sub-optimal conditions to properly align a vehicle when an aftermarket lift kit and an ICON tubul
Does the factory sway bar have to be removed when installing 2007-UP Toyota Tundra 3.0 Series coilovers?
No, the ICON 3.0 Series coilover system was designed to allow the factory sway bar to be retained. The ends of the factory sway bar will have to be clearanced but the sway bar will remain on the vehicle. If there is an interference issue with the swa
Do ICON 07+ Toyota Tundra coilovers require a sway bar relocation kit?
No, the factory sway bar does not require to be re-position or adjusted on the 07+ Toyota Tundra when installing ICON coilovers.
My 2007-UP Toyota Tundra coilovers came with two different size spacers for the lower mount - what is the correct orientation?
For 2007-UP Toyota Tundra the large spacer should be oriented forward to position the lower shock mount in the lower control arm correctly. The lower shock mount will be offset rearward to allow enough clearance between the lower shock mount pocket w
Will the 3.0” Tundra coil overs provide more left than 2.5” Tundra coil overs?
No, the ICON 3.0” Series coil over will not provide more lift over stock than the 2.5” Series. If more lift is desired the ICON bump stock spacers are recommended to allow a larger max thread showing. 51046 - 07-UP TUNDRA/200 SERIES BUMP STOP SPACER
Can I convert my 2007-2020 Tundra IFP coil overs to remote reservoir or CDCV?
Yes, non-reservoir coilovers can be upgraded to either Remote Reservoir or CDCV. 51037 - 07-UP TUNDRA RESI UPGRADE KIT W/SEALS PAIR. 51037C - 07-UP TUNDRA RESI CDCV UPGRADE KIT W/SEALS PAI. Reservoir upgraded kit include all the necessary parts requi
Can 2007 - 2019 Toyota Tundra coil overs be upgraded to a heavier rate coil spring?
No, Icon does not offer a heavier rate coil spring for the 2007+ Tundra. There are other spring manufacturers that make a coil spring of similar dimensions to the icon coil spring, however the max thread showing would have to be calculated based on t
Can the ICON 51200 rear expansion pack be installed without the over load leaf?
No, the Tundra expansion pack was designed to retain the factory overload leaf. Failure to install this kit correctly will cause premature wear on the leaf pack as well and loss of lift height. Contact ICON tech-support for more details (951) 689-ICO
Are aftermarket upper control arms required on the 2007-UP Toyota Tundra systems?
No, but it is highly recommended. Aftermarket upper control arms are not required for a 2007-UP Toyota Tundra when setting the vehicle below 2.5" inches of lift over stock. However, lifting the Tundra over 2.5” with the the stock upper control arm wi
Is there a heavier rate spring option for the ICON Toyota Tundra 3.0 Series coilovers ?
No. Due to the very specific specs of the spring on the ICON 3.0 Series coilover, a heavier coil option is not available. The wire in the spring is special order and a heavier coil spring will actually yield less travel than the current production sp
Can ICON 07+ Tundra coil overs work with long travel suspension systems?
No, remote reservoir coilovers do not carry over to long travel systems. The coilovers will require changing the rodend, hiem spacers, shock shaft and coil spring in order to convert one of the two long travel applications:. 58750 - 07-UP TUNDRA 2.5
My 07+ Tundra coil overs are currently set to the maximum thread showing, what can I do to get more lift?
If you are currently at the max thread recommendation there is an option available to provide more lift. The max compressed length for front suspension is determined by the factory bump stops. The max thread showing is set with this dimension in mind